Four (4) x 60 ton hydraulic Mooring Winches made by Brissonneau & Lotz France.
The single drum winch is powered by  186 cm3/rev high volume Linde motor that gives a line
pull of 60 ton at the 1st layer with line speed of 9 m/min, brake holding capacity on 1st layer
of 110 ton.
Drum storage capacity : 1000 meter of 52mm in 15 layers

Article number: 040
Date of construction: Jan 1, 2009
Price: On request

The winch would comprise a single main plain cored drum of fabricated construction, fitted with phosphor bronze bushes, running on a high tensile steel main shaft. The main shaft would be supported on the fabricated base plate by heavy roller type bearings, mounted in steel housings, bolted to the winch base frame.
Mounted to the winch drum flange, would be a fabricated brake track, fitted with a hydraulically released and spring applied bake, giving a failsafe to On-Mode of operation. The brake assembly would comprise a fabricated brake band, hinge pins with mechanical linkages, adjusting screw, hydraulic cylinder and return spring.
The brake linings are a non asbestos marine grade.
Transmission would be from to two low speed high torque medium pressure hydraulic motors, driving through a totally enclosed spur reduction gearbox, driving in to a final drive guarded spur reduction gear set.
Also fitted to the main gearbox output drive pinion would be a hydraulically operated dog type clutch. The clutch is used to disconnect and protect the hydraulic drive motors during high speed payout, when the drag is in operation.
Fitted to the spur gearing at the front side of the winch would be a fresh water cooled air controlled drag brake to assist with back tensioning when running out the wires by the anchor handling tug.
An automatic wire spooling system would be provided, designed or under drum reefing, comprising a lead screw and drive tongue, fabricated carriage with bushed vertical rollers, guide bar, side support frames, chain drive system including driver and driven chain wheels, chain, guard and a manually operated positioning clutch.
The winch base plate would be suitably drilled to allow the fitting of the winch to the deck settings by means of your free issue holding down bolts.
Specifications per winch
Duty Pull at Layer One                      – 85.0 tonne @ 0 – 12.0 mtr/min
– 59.0 tonne @ 0 – 17.0 mtr/min
– 28.0 tonne @ 0 – 32.0 mtr/min
Duty Pull at Layer Six                       – 52.3 tonne @ 0 – 19.5 mtr/min
– 36.3 tonne @ 0 – 27.6 mtr/min
– 17.2 tonne @ 0 – 52.0 mtr/min
Duty Pull at Layer Eleven                   – 37.8tonne @ 0 – 27.0 mtr/min
– 26.2 tonne @ 0 – 38.2 mtr/min
– 12.4 tonne @ 0 – 72.0 mtr/min
Drum Capacity                                 – 1500mtr x 52mm dia. Wire Rope in eleven layers
Brake Holding Load                           – 150.0 tonne @ First Layer
Drag Brake at Layer One                   – 10.0 tonne @ 0 – 100.0 mtr/min
Drum Core Diameter                         – 780mm
Drum Flange Diameter                       – 2,500mm (One free layer)
Drum Flange Distance                        – 1,760mm
Oil Flow                                         – 600litre/min
Working Pressure                            – 230 BAR
Power Requirement                         – 270kW Approx

Article number: 020
Date of construction: Jan 1, 1996
Price: On request

125 tons Brissonneau & lotz Anchor Mooring Winches with wire capacity of 1500 meter dia. 76mm.
Brake holding capacity 300 tons, hydraulically powered by Linde motor type HMF 135-02.
On the gearbox there is a manual clutch for using the winch on 35 ton with high speed and
125 ton with low speed. Dimensions : Length 4,50 meter x Width 3,55 meter x Height 3,50 meter.

Article number: 016
Date of construction: Jun 1, 2009
Price: On request

Six (6) pieces Hydraulic Mooring Winches made by Ridderinkhof with pulling capacity of 60
tons at First layer, powered by Hägglunds motor MB 84 38000
Low speed : 7,5 meter/min and high speed at 22,5 meter/min.
Power support at 252 liter/min at 225 bar.
Max Hold on break at 100 tons on first layer

Article number: 028
Date of construction: Jan 1, 1996
Price: On request

60 tons hydraulic towing winch made by Stocznia Szezecinska Poland.
Pulling 60 tons powered by Linde motor with wire capacity of 1020 meter on 6 layers,
diameter 39mm or 42mm inclusive spooling device. Weight 14 ton

Article number: 026
Date of construction: Jan 1, 1987
Price: On request

Three (3) side by side winches with additional working drums and on both sides warping
heads. Pulling capacity 30 tonnes on the two main drums with 600 meter dia. 30mm steel
wire in 14 layers. Winches do have friction clutches and automatic brakes to have free fall.

Article number: 021
Date of construction: Jan 1, 2010
Price: On request
Single drum 35 tons hydraulic Anchor Mooring Winch with auto spooling device with manual
de-clutch, open spur gear & pinion with cover. Brake maximum 90 ton static on 1st layer,
hydraulic operated, manual override with hydraulic claw type clutch, warping head dia. 450mm.
Hydraulic motor  : Intermot AM 4600 H7 A1 D90

Article number: 004
Date of construction: Jul 1, 2007
Price: On request
Electric Mooring Winches Type EMO 34/2S-2, split type, Dimensions; dia 368 / dia. 1675
455 + 470 mm length for storing 220 m rope ø56 mm in 2  + 10 layers. Breaking load
of the rope: 688kN.
Each drum provided with dog clutch and band brake, both hand operated.
With 2 warping head, cast steel dia. 375mm, coiling dia. 430mm, fixed on the mainshaft.
All shafts running on largely dimensioned roller- or ball bearings.
Totally enclosed reduction gearbox, oil bath lubrication. Number of mechanical speed steps;
1 Standstill heating foreseen in the oil bath with thermostat.
Electric motor flange mounted on gearbox, parallel to the main shaft.
The brake bolts and spindles are made of stainless steel and with individual grease nipples.
All pivot points equipped with stainless steel shafting with bronze bushes, all to be fitted with
brass grease nipples.

Kind regards,
Toon Coenraadts

3 Responses to 533 – 20 X WINCH FOR SALE

  1. Superwinch says:



  2. FELICI says:

    Good day
    Can you confirme Price and area to inspect Winches

  3. FELICI says:

    please give us price and area to inspect winches

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

%d bloggers like this: